Method and method of fabrication and stitching of quartz stone table

Number of visits:information sources:Shandong Kang Jieli New Materials Co., LtdRelease time:2018/7/11

Quartz stone concrete application, can not avoid two pieces of splicing or even multiple pieces of splicing, because the hardness of quartz stone up to 7 level moth, splicing, in order to make the whole look like a whole, the test of quartz stone manufacturers and processing master technology. Specifically how to operate, we can click the way to operate.


The mutual inspection of all the large and small materials includes the direction of the skirt, the position of the edge, the direction of the slope, the length and the width of the skirt, and the color difference between the spliced plates. Before making, we need to understand the side structure and the size of the small materials, so that we can have a good idea and do not glue the wrong edges.
Place the bottom of the panel on the table and on the worktable, check the smoothness of the adhesive surface, wipe off the stains with clean balls, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. According to the thickness of the table, select the corresponding height of the skirt reinforcement bar (the height of the reinforcing bar h=h - D), and evenly apply the coloring cloud and stone glue to bond the light surface to the bottom of the table, and the outer edge of the reinforcing bar is leveled with the slope of the panel. It is clamped with G clip or a type clip to clear the residual glue. Evenly smear the coloring and coloring micelle with the slope side of the panel and the side side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with the F clip, and tap the moderate strength with a rubber hammer. It is the flat of the skirt and the panel at the corner. A clip is clipped at every 100-150mm. Then use the A clip to clamp the skirt and reinforcement plate between each two F clips to clean up the residual glue. The bottom of the reinforcement class is flat with a flat flat surface, so that the width of the skirt is 65mm, and the clip is fixed every 200mm.
Put the bottom of the panel up on the worktable, check the smoothness of the adhesive surface, wipe off the stains with clean balls, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. According to the thickness of the table, select the corresponding height of the skirt reinforcement square (the specification of the reinforcing square is 35 x h, h=h-2d), and evenly smear the color and marble glue to bond the reinforcing block to the bottom of the table every 200mm away, and the reinforcing square is flat on the side of the panel. It is clamped with G clip or a type clip to clear the residual glue. Evenly smear the coloring and coloring gels on the side side of the panel and the side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with the f clip, and use the rubber hammer to moderate the strength, make the edge of the skirt flush with the panel, and clip a clip at every 100-150mm. Then use the G clip to clamp the skirt and reinforcement block between each two f clips to clean up the residual glue. The bottom of the reinforcing plate is flat and adhered to a flat strip of smooth surface, so that the width of the skirt can reach 65mm, and it is clamps every 200mm.
Place the surface of the panel up on the worktable, check the smoothness of the adhesive surface, wipe off the dirt with clean ball, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. Evenly smear the coloring and coloring gels on the side side of the panel and the side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with a type clip and use the rubber hammer to moderate the strength, make the skirt and the panel at the corner flat, and clip a clip at every 100-150mm. Clean up residual glue and enter the next process after 15 minutes.

Relevant labels:
       TECHNICAL SUPPORT:Jining Network Company FeiXun Network

Hotline

400-628-6606
Free service hotline

Wechat

Focus on Wechat Public Platform